- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
				
					  Marine Mechanic in the Rancho/Upland/Ontario area
				
				
						
							
							
						
						
				
					
						
							Can anyone recommend a good marine mechanic in this area?   
Need help doing a simple tune up and getting the boat running.  
 
I replaced all fuel lines, had the carb rebuild and put in a fresh set of batteries and I can not get it to turn over.  It wants to but does not fire.  I tried it three times and on the third, there was a loud noise I can describe as a back fire.  I swear it sounded like someone shot a 357 behind the boat.   
 
Anyways, I do not want to damage anything further in case it was not a back fire and so I am looking for a place to take it into.   
 
I should note I took the distributor off with spark plug wires and I have it wired in this order.  1-8-4-3-6-5-7-2 
Yes I am an Amateur lol
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
		
			
				
				
						
						
				
					
						
							Did you take the whole distributor off or just the cap and wires, or just the wires off the cap? Sounds like your timing is off. I would bet you have the cap mis wired or the timing is too retarded if you actually took the dist out of the motor.
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
						
						
				
					
						
							Im a winner and took the whole shaft out of the engine.  I see that the distributor only fits in 1 way so I placed it in and have it sitting flush.  So is the timing off because I took the entire shaft out?
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
		
			
				
				
						
						
				
					
						
							We have several local Marine shops in the area you can refer to the advertisers section for contact and phone number.  Good luck and I'm sure someone will chime in, but give them a call.
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
						
						
				
					
						
							
	
		
			
			
				
					  Originally Posted by  riverrunner1984
					 
				 
				Im a winner and took the whole shaft out of the engine.  I see that the distributor only fits in 1 way so I placed it in and have it sitting flush.  So is the timing off because I took the entire shaft out? 
			
		 
	 
 If the distributor is turned at all, even a tiny bit, the timing is off and should be set with a light.  How big is the boat?  I don't normally like running engines here since I am in a residential neighborhood, but am right off the 210 freeway at the San Dimas/Glendora border, might be able to fix it up pretty quick.
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
						
						
				
					
						
							It is a 19ft boat on a double decker trailer (waverunner on top of course)   
Be great if you could fix it!
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
				
					Marine Mechanic in the Rancho/Upland/Ontario area
				
				
						
						
				
					
						
							Timing may be 180 out. The distributor actually drops in two ways and it could have turned 180 degrees while you had it out. It is possible that it is in close to right and still backfired but I'm guessing it is off by a lot. I would love to help but I realize Valencia is a bit of a drive for you. You are welcome to give me a call and I can walk you through it.  
Dustin 
661-755-0620
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
				
					Marine Mechanic in the Rancho/Upland/Ontario area
				
				
						
						
				
					
						
							If obnoxious can help you out you are in good hands as well. Barry is a good guy.
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
						
						
				
					
						
							Big shout out and thanks to Barry (obnoxious001) for helping me out last night!   
As an amateur, I had no idea how much goes on in the engine area if you will.   
Thanks again!
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
- 
	
	
		
			
			
				Senior Member
			
			
			
			
			
			
				 
			
			 
			
				 
				
				
				
				
					    
				 
			
		 
		
			
				
				
						
						
							
						
				
					
						
							
	
		
			
			
				
					  Originally Posted by  riverrunner1984
					 
				 
				Big shout out and thanks to Barry (obnoxious001) for helping me out last night!   
As an amateur, I had no idea how much goes on in the engine area if you will.   
Thanks again! 
			
		 
	 
 Very cool! Glad you got it fixed  
						 
					 
					
				 
			 
			
			
		 
	 
		
	 
 
		 
		
		
	
 
	
	
 
	
	
	
	
	
	
	
	
	
	
		
		
		
		
			
				 
				Posting Permissions
			
			
				
	
		- You may not post new threads
 
		- You may not post replies
 
		- You may not post attachments
 
		- You may not edit your posts
 
		-  
 
	 
	
	Forum Rules 
 
			 
		 
	 
 
  
 
 
 
			
			
		
			All times are GMT -7. The time now is  11:40 PM.
 
	
	
	
	
	
 
			vBulletin Skin By:  PurevB.com	
		
		 
		
			 
 
   
 | 
  
Bookmarks