Lets see if we can start a thread about boats

I may get over today to take some pics of an old fuel hydro currently getting restored.

Quote:

---

Originally Posted by ogshotgun

lets try again its a thread about boats .. not a picture contest ... lets talk about boats and boats only so iask what do you have ?

---

og, I have somewhat the same concerns for a site that calls itself HOTBOAT, but the way I see it, you have 2 choices, add content, or find content where you can find it. Every site has its "SANDBOX" where non boating topics are discussed. This site as another as another, has more than a reasonable share of threads on non boating topics. If it bothers you, stay out of the sandbox, and post your boating stuff else where on the site.
Too date, the majority of YOUR posts have been non boating as well, and fit better into the whinning and bitching forum.

If YOU have something to say or add, please do so. This is the forum we "talk boats"

YOU may even find it helpful in your case helpful if you SFU and read. You might actually learn a little here.

Here is a Thread build of OG boat in the v drive section. http://www.hotboat.com/frm/showthrea...-2013-phase-II

Quote:

---

Originally Posted by WMC

Here is a Thread build of OG boat in the v drive section. http://www.hotboat.com/frm/showthrea...-2013-phase-II

---

Saw it. lot of "show" very little "tell"
I wouldn't want to try and restore a row boat with the content in that thread. Look more like a photo album from his Facebook page.
Cool stuff, cool boat. But from a guy BITCHING about content, I would have expected a more than LAM thread.

Quote:

---

Originally Posted by gn7

Saw it. lot of "show" very little "tell"
I wouldn't want to try and restore a row boat with the content in that thread. Look more like a photo album from his Facebook page.
Cool stuff, cool boat. But from a guy BITCHING about content, I would have expected a more than LAM thread.

---

It is a cool boat he posted pictures of originally. As a project it is about where some of mine are, a long ways from being a boat again. He does seem to work hard, or at least someone is. But it might be best if he didn't give too much commentary on how to do things right. His explanation of jet boat headers is priceless. I even made it my signature line.

On looking back at the picture he posted, he might not have Jet Boat headers, but man is that engine angle up there. Not a good combination if you like to turn at speed..

Quote:

---

Originally Posted by gn7

Jerry, I take it you haven't seen the half dozen braiding machines 2MM has.

https://www.youtube.com/watch?v=v7cHdo35jrA

---

He probably builds the machine first. :D

Hey, I have a boat.

Getting ready to spray some red on the Red Baron. With Rhinowood, After You 362, and Fred Romani. Attachment 32147Attachment 32148

Sent using Tapatalk.

Quote:

---

Originally Posted by RogerThat99

Getting ready to spray some red on the Red Baron. With Rhinowood, After You 362, and Fred Romani. Attachment 32147Attachment 32148

Sent using Tapatalk.

---

What are you up to over there??


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by 2manymustangs

YOu or someone "built" a new set of plates for you HONCHO right? In so doing did you melt the aluminum, pour it, roll the ingot into plate stock BEFORE you saw cut/drilled/Csink'd the holes?

YOu are prolly aware that braided stainless likes are a TAD more involved than just spooling off some Gates 5/8" rubber heater hose, pushing them onto the barbed fittings and tightening the hose clamps... Right???
Do you "BUILD" brake lines? or do you just cut them from bulk and throw them on the car, tighten them down???

---

OK 2MM. lets not try to make it sound like you are assembling a blown SOHC here. Its some hose and a couple ends. Not exactly rocket science. Getting the money out of your wallet is the hardest part of plumbing a boat.