Page 1 of 3 123 LastLast
Results 1 to 10 of 113

Hybrid View

  1. #1

    A 76 Hondo GT comes home

    I posted a picture and this brief description in the Wild V Drives Thread, Sharp Shooter recommended that I post a build thread here so here goes - flame away.

    Hello all, new to this forum but not new to dragboats. My dad raced flats from the late 60's through the 80's here in the mid west and then I ran the Hondo GT pictured below through the 90's. Sold the boat in 2000 and never thought I'd see it again, it sat in a barn for 13 years collecting dust till the guy who bought it from me called and asked if I wanted it back. She's going through a partial restoration to start her new life as a lake rod / part time bracket racer for fun. I bought this boat for the first time in 1990, restored it, then had a great racing career with it. With the help of my family, we wound up with 6 high points championships and even managed a Driver of the year award in 1996. I'm really glad to have it back, it's like a member of the family!
    Name:  006.jpg
Views: 586
Size:  84.5 KB

  2. #2
    So here we are picking up the boat last summer and sitting in the seat for the first time in 13 years!
    Name:  photo 2.JPG
Views: 590
Size:  100.1 KBName:  photo 3.JPG
Views: 550
Size:  120.9 KB

  3. #3
    After we got it home and took a good look at it we decided all the hardware needed to come out and replaced, it was all well worn after it's racing career. Also decided that the floors needed to be refinished, found some delam on the stringers in spots plus the floors just looked bad so I started grinding fiberglass.....
    Name:  Boat Floor1.jpg
Views: 695
Size:  145.1 KBName:  Boat Floor3.jpg
Views: 681
Size:  122.9 KB

    What a horrible job and I will never do this again - much of the summer of 2013 was spent being very itchy from fiberglass dust.

  4. #4
    The original wood looked good after all the grinding, too bad I made a few rookie mistakes and ground through the top layer of it in a few spots. So I laminated down a layer of end-grain balsa and got some epoxy / cloth back over the floor by late fall. I went with epoxy because it's easier to work with, doesn't stink and is supposed to perform very well.
    Name:  balsa.jpeg
Views: 598
Size:  109.9 KB

  5. #5
    After the epoxy cured I started finish sanding in preparation for flow coating, I decided that I should start fabbing the new hardware before the final flow coat so I wouldn't have to worry about scratching it.
    Name:  image.jpg
Views: 683
Size:  103.8 KBName:  image.jpg
Views: 659
Size:  84.0 KB[ATTACH=CONFIG]
    As you can see, everything is going to be new.
    Last edited by OhHondoGT; 05-13-2014 at 02:17 PM.

  6. #6
    My brother decided to get in on the act and buy a Hondo flat to have some fun with, He purchased this 76 Hondo from Top Fuel racer Mike Robbins in North Carolina. It's getting new hardware also and a floor rehab, but he decided not to go as far as I did and I don't blame him.
    Name:  image.jpg
Views: 551
Size:  115.9 KB
    Last edited by OhHondoGT; 05-13-2014 at 02:15 PM.

  7. #7
    Name:  image.jpg
Views: 567
Size:  83.2 KBName:  image.jpg
Views: 548
Size:  73.0 KBA few more hardware pics..
    Name:  image.jpg
Views: 551
Size:  79.7 KB

    At this point we're done fabbing and getting back on finishing the floors - more updates as soon as I have them.
    Last edited by OhHondoGT; 05-13-2014 at 02:20 PM.

  8. #8
    Already miss the 310/562 2manymustangs's Avatar
    Join Date
    Sep 2013
    Location
    314 ish....
    Posts
    6,050
    Quote Originally Posted by OhHondoGT View Post
    After the epoxy cured I started finish sanding in preparation for flow coating, I decided that I should start fabbing the new hardware before the final flow coat so I wouldn't have to worry about scratching it.
    Name:  image.jpg
Views: 683
Size:  103.8 KBName:  image.jpg
Views: 659
Size:  84.0 KB[ATTACH=CONFIG]
    As you can see, everything is going to be new.
    Very nice work... AND FORD POWER!!! TELL ME MORE, please...
    -In a Republic, the sovereignty resides with the people themselves. In a Republic, the government is a servant of the people, and obliged to its owner, We the People..

    "Remember, democracy never lasts long. It soon wastes, exhausts, and murders itself. There never was a democracy yet that did not commit suicide." John Adams

  9. #9
    Quote Originally Posted by 2manymustangs View Post
    Very nice work... AND FORD POWER!!! TELL ME MORE, please...
    Thank you. The engine is 525ci, pump gas, 10:1 compression. Ford Super Cobra Jet aluminum heads with a quick fuel 1050 carb. I had it in my 96 Mustang last year that went 9.82 at 139 foot braking so it makes decent power (about 630), I want to try a little bigger cam and a different intake for the boat to see if it will make a little more power. Really hope to run 10 ohs on pump gas, we'll see?

  10. #10
    Quote Originally Posted by OhHondoGT View Post
    After we got it home and took a good look at it we decided all the hardware needed to come out and replaced, it was all well worn after it's racing career. Also decided that the floors needed to be refinished, found some delam on the stringers in spots plus the floors just looked bad so I started grinding fiberglass.....
    Name:  Boat Floor1.jpg
Views: 695
Size:  145.1 KBName:  Boat Floor3.jpg
Views: 681
Size:  122.9 KB

    What a horrible job and I will never do this again - much of the summer of 2013 was spent being very itchy from fiberglass dust.
    I just noticed the riding mower is your tow vehicle in this shot. Nice!!

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •